Pages

Sabtu, 02 April 2016

Window Trim Fascia A Photo Essay

This is a little out of the norm for a post here at the Penultimate Woodshop, but I was working on the trim to my bay window today and I photographed the milling of the relatively complex (for a fascia board) trim which caps the sides of the bay window. I thought Id take a brief break from the Wanderful Saga and present the fascia milling photos as a photo essay. The trim is Versatex PVC and once milled it is fastened using stainless steel trim head screws. Here goes:
The trim piece set up under the jig I made for milling the 30 degree angles next to a test piece.
Milling the angle.
Using relative dimentioning to mark the slight cut that gets made at the end.
Cutting perpendicular to the main 30 degree cut. This cut to to adjoin the fascia  on the wall adjacent to the window. Yes, I know the saws not cutting, but I couldnt cut and take a photo at the same time.
All cut.
Determining the width of the fascia above the window by referencing the adjoining fascia.
About to cut of the excess at the other end.
Cut and ready for milling.
Determining the router bit depth by adjusting it to my line.
Marking of the angled cut needed to fit tight to the soffit, which is not plumb.
Using a melamine shelf as a reference for the bushing guided bit to mill the angled cut.
I didnt clamp the melamine to the trim piece well enough and made a small mess with the cut. Luckily this is the top and the joint between the fascia and soffit will get caulked anychoice so I can hide this.
Trimming the wide end ever so slightly so that it is perfectly flush with the adjoining fascia piece.
A test fit. So far, so good.
Milling the notch to accommodate the window.
I clamped this board to the fascia piece and used it as a reference for my hand saw to square up the router cut.
Cleaning up the inside corner (yes, you can chisel PVC trim).
The notch to accommodate the window.
A nice, tight fit between the fascia on the side of the window and the fascia along the eave.
The installed fascia piece.
The next piece of trim to mill and install will the the extension of the eave fascia to bring its bottom edge flush with the fascia on the sides of the window. Ill biscuit the fascia along its length to ensure the pieces stay flush.
The bay window, almost completely trimmed.
Read More..

Wolf Achievement 5

Have you shared woodworking with anyone? Thanks, if you have. If not, please do. Remember, it’s Get Woodworking Week. It’s important that we all share our craft with others so that this obsession we call woodworking will continue for generations to come. I shared a very basic introduction to the craft with about two dozen eight year olds this year.My twin sons have been Cub Scouts for two (2) years. They’re currently Wolves. While I’m not an official leader, I’m a relatively involved parent. I certainly try to help out when I can.
Im proud to say the Plotke cars dominated taking first in class and first overall.
Last week, our Pack held our Pinewood Derby night. It was a triple event night, consisting of a spaghetti dinner fundraiser, achievements for each level scout and, of course, the derby. The achievement the Wolves worked on was Achievement 5: Tools for Fixing and Building. I taught the achievement to the four (4) Wolf dens.I followed the basic instructions set out by the Wolf Book, so we began by learning the names and uses of several tools. Though they weren’t the first dozen tools I’d have considered, we discussed: claw hammers, coping saws, C-clamps, hand saws, awls, hacksaws, files, adjustable wrenches, straight blade screwdrivers, phillips screwdrivers, slip joint pliers and needle nose pliers.After showing and reviewing each tool’s purpose and method of use, I broke the kids into smaller groups and the were able to work with the hammers, both types of screwdrivers and both types of pliers.
Controlling the force of the hammer blow vs controlling the aim was
critical for the Wolves.
The hammer demonstration was as simple as it sounds, just a bunch of 8 year olds hitting nails into a 2x4 on the floor.
It took all the force they could manage to hand drive the Phillips head screw.
Driving the straight head machine screws was much easier.
For the screw driver demonstration, we used the awl to make a starter hole, then drove phillips head wood screws into a 2x4 by hand. Though the Wolf Book says to do a similar thing with a straight blade screw, I didn’t have the heart to punish them by making them drive a straight blade screw in by hand. Instead, I epoxied some nuts into a board and had them drive straight blade machine screws into the nuts.The plier demonstration was the most fun. The book reviews how to use slip-joint pliers for both thin and thick items. For the thin item with the jaw closed, I had the boys move a piece of sheet metal between slots in two (2) 2x4’s. For the thick item, I had them move a copper pipe between two (2) holes in a 2x4. Since I most often use needle nose pliers while doing electrical work, I had the kids use the wires to bend a hook on the end of some small wires, then hand the wires on screws I had partially driven into a scrap of plywood.
These 1x6s will soon be birdhouses.
The final requirement for Achievement 5 will be the construction of bird houses. We were originally supposed to build them last Friday, but since I was sick all week, we’ve postponed the bird houses until our 2/21 den meeting.As the boys get older we’ll take them through more complex projects. For about two dozen eight year olds, it was fun to just introduce them to some tools and show them how they worked.
Read More..

And The Teasing Begins

The Woodworking In America 2013 website has just gone live. You can check out all the details here. Unfortunately, you cannot get tickets just yet. Those are promised later this month.
In the mean time, its well worth checking out the site to see speakers, review the classes and begin drooling over the marketplace vendors. As youre reviewing the classes and building your itinerary, keep Saturday afternoon/evening open. Youll be sure to enjoy the Online Woodworking Roundtable. My fellow Modern Woodworkers Chris Adkins and Tom Iovino will be among the distinguished panelists  (making the panel just slightly less distinguished).
You can see more about WIA 2013 in this years promo video. 
Read More..

Back to Sea

Just a quick Blog update ... Not much wood working action recently as indicated by the lack of posts.
I am busy preparing to deliver a nice little J92 racing yacht from the UK across Biscay and through the Gibraltar straits to the south coast of Spain. 
I will be gone for a few weeks but there will definitely be more projects when I get back.
See you all soon...
Read More..

Dads Benchtop Bench Part V

With the bench built, all that was left was to screw in the two veneer press screws which held on the front vise jaw.
The completed benchtop bench.
While they fit fine, I unfortunately found that once I tightened them, the handles came off the screw shaft. It seemed that since they were meant to exert pressure between the vise nut and the end of the screw shaft, Shop Fox hadnt bothered to attach the handles with anything more than friction.
Nope. That handle wasnt meant to exert clamping pressure.
While the discovery of this issue after I thought I was done did give me pause, I thought about it for a night and by morning I’d come up with a solution.
The pins and drill bits. I only needed 2. I bought 4 just in case.
Locked and ready to drill.
I headed down to the hardware store and picked up some metal pins. After drilling through the handle and screw shaft with my drill press, the pins were easy to knock in with a hammer.
Locked and ready for action.
Once the handles were pinned on, the vise worked great.
Clamping like a champ.
I’m very happy with the choice the benchtop bench came out, and my Dad appreciated it as a father’s day gift.
Read More..

Jumat, 01 April 2016

A House In The Trees Part XVI

Two days into a three day weekend and Im making progress. The decking is now well underchoice.
Dont forget about the +Modern Woodworkers Association Podcast. We talk woodworking with guests from around the world of woodworking every other week. Subscribe to the RSS feed or iTunes today.
Read More..

New ASDOO video

Read More..